Differences

This shows you the differences between two versions of the page.

--- hardware:mikrotik [2022/10/20 19:49] – [mikrotik.configure.vip sip] admin
+++ hardware:mikrotik [2024/02/26 16:25] (current) – [Microtik VLAN] admin
@@ Line 68: / Line 68: @@
 ===== mikrotik.packet sniffer tcpdump =====
+  * для работы torch + sniffer нужно отключить ''hardware offload в bridge -> ports -> eth0 -> hardware offload ''
   * https://wiki.mikrotik.com/wiki/Manual:Layer2_misconfiguration - если нужно перехватывать на уровне layer 2 - раздел "Packet flow with hardware offloading and MAC learning"
   * https://wiki.merionet.ru/seti/6/perexvat-paketov-na-mikrotik/
@@ Line 109: / Line 110: @@
 ==== Microtik VLAN ====
+<code BASH>
+# Пример настройки VLAN  с SWITCH  chip, native vlan - :!: в mikrotik NATIVE VLAN = VID:0
+[admin@MikroTik-304] > /interface/ethernet/switch/vlan/
+[admin@MikroTik-304] /interface/ethernet/switch/vlan> export
+# feb/25/2024 19:05:42 by RouterOS 7.8beta2
+# software id = W523-SWBT
+#
+# model = RBD52G-5HacD2HnD
+# serial number = BEEB0A75E122
+/interface ethernet switch vlan
+add independent-learning=yes ports=ether1,switch1-cpu switch=switch1 vlan-id=112
+add independent-learning=yes ports=ether1,ether5,switch1-cpu switch=switch1 vlan-id=111
+add independent-learning=yes ports=ether1,switch1-cpu,ether2,ether3,ether4,ether5 switch=switch1
+[admin@MikroTik-304] /interface/ethernet/switch/vlan> /interface/ethernet/switch/port
+[admin@MikroTik-304] /interface/ethernet/switch/port> export
+# feb/25/2024 19:05:54 by RouterOS 7.8beta2
+# software id = W523-SWBT
+#
+# model = RBD52G-5HacD2HnD
+# serial number = BEEB0A75E122
+/interface ethernet switch port
+set 0 default-vlan-id=0 vlan-header=add-if-missing
+set 1 default-vlan-id=0
+set 2 default-vlan-id=0
+set 3 default-vlan-id=0
+set 4 default-vlan-id=111 vlan-header=always-strip vlan-mode=secure
+set 5 default-vlan-id=0
+[admin@MikroTik-304] /interface/ethernet/switch/port>
+#  WIFI configure
+# Under /interface ethernet switch vlan switch1-cpu passes traffic from the switch chip to the CPU, only required for VLANs connected to services provided by the CPU such as IP address, routing, DHCP server and software-based # interfaces (tunnels, wireless).
+# Under /interface ethernet switch port use vlan-header=leave-as-is for the switch chip in the hAP ac as mentioned in the wiki and help pages.
+# Under interface wireless use both vlan-mode=use-tag AND vlan-id= to specify which VLAN the interface should be connected to.
+# Under /interface bridge port setting hw=yes for the wireless interfaces is pointless, the drivers are implemented in software.
+</code>
   - https://danservices.com.au/support/mikrotik-vlan-configuration-2020/
   - https://www.youtube.com/watch?v=pdpFAxwocTo
   - https://mum.mikrotik.com/presentations/HU19/presentation_6775_1559545769.pdf